DIN EN 61558-1-1998 电力变压器安全性.供电设备及类似设备.第1部分:一般要求和试验
作者:标准资料网 时间:2024-05-07 02:04:55 浏览:9907
来源:标准资料网
【英文标准名称】:Safetyofpowertransformers,powersupplyunitsandsimilar-Part1:Generalrequirementsandtests(IEC61558-1:1997,modified);GermanversionEN61558-1:1997
【原文标准名称】:电力变压器安全性.供电设备及类似设备.第1部分:一般要求和试验
【标准号】:DINEN61558-1-1998
【标准状态】:作废
【国别】:德国
【发布日期】:1998-07
【实施或试行日期】:1998-07-01
【发布单位】:德国标准化学会(DIN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:性能;安全要求;电源设备;供电系统;主变压器;电气工程;规范(验收);一般条件;电力变压器;定义;试验;变压器;机械安全;安全;电气安全;防火安全
【英文主题词】:
【摘要】:
【中国标准分类号】:K41
【国际标准分类号】:29_180
【页数】:109P;A4
【正文语种】:德语
【英文标准名称】:ISOsystemoflimitsandfits;basesoftolerances,deviationsandfits;identicalwithISO286-1:1988
【原文标准名称】:ISO公差配合系统.第1部分:公差基础.偏差和配合
【标准号】:DINISO286-1-1990
【标准状态】:作废
【国别】:德国
【发布日期】:1990-11
【实施或试行日期】:
【发布单位】:德国标准化学会(DE-DIN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:尺寸;公差;极限尺寸;ISO配合;尺寸公差;基本公差;标准公差;偏差;配合;基本偏差;极限偏差
【英文主题词】:Basicdeviations;Basis;Compositionaltolerances;Definitions;Designations;Deviations;Dimensionaltolerances;Dimensions;Englishlanguage;Fits;Frenchlanguage;Fundamentaltolerances;ISO;ISOfits;Japaneselanguage;Limitdeviations;Limitdimensions;Ratings;Russianlanguage;Schematicrepresentation;Shafts(rotating);Spanishlanguage;Standardtolerances;Symbols;Terminology;Tolerancezones;Tolerances(measurement);Wells
【摘要】:ThestandardgivesthebasesoftheISOsystemoflimitsandfitstogetherwiththecalculatedvaluesofthestandardtolerancesandfundamentaldeviations.Thesevaluesshallbetakenasauthoritativefortheapplicationofthesystem.Thestandardalsogivestermsanddefinitionstogetherwithassociatedsymbols.TheISOsystemoflimitsandfitsprovidesasystemoftolerancesanddeviationssuitableforplainworkpieces.
【中国标准分类号】:J04
【国际标准分类号】:17_040_10
【页数】:36P.;A4
【正文语种】:德语
Product Code:SAE ARP6109
Title:Electronic Engine Control Hardware Change Management
Issuing Committee:E-36 Electronic Engine Controls Committee
Scope: The scope of this standard is the configuration management process. The configuration management is requested from airworthiness point of view but not only. The mains requirement from the regulation are the following:
Rationale: The scope of this standard is the configuration management process. The configuration management is requested from airworthiness point of view but not only. The mains requirement from the regulation are the following:
